Name: HC-05 Bluelink 5V TTL (rhydoLABZ)
Brand: rhydoLABZ
Price: 449.00 INR
Availability: OutOfStock

HC-05 Bluelink 5V TTL (rhydoLABZ)

Stock: Out Of Stock
Brand: rhydoLABZ
Model: WRL-2509
Weight: 0.05kg
MPN: WRL-2509

Based on 0 reviews. - Write a review

Rs 449.00

(Excluding GST)

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Description
Reviews

Description: HC-05 Bluelink is a compact Bluetooth Module ( 5V Serial TTL) from rhydoLABZ. The module comes with built in 3.3V Voltage regulator. It is only having 5pins (Standard 2.54mm bergstrip) VCC,GND,TX,RX and RESET. The module is factory configured in Transparent Mode. So there is no command required for normal operation.

The BlueLINK is a Drop-in replacement for wired serial connections, transparent usage. You can use it simply for serial port replacement to establish connection between MCU and GPS, PC to your embedded project / Robot etc. Any serial stream from 9600 to 460800 bps can be passed seamlessly from your PC/PDA/MOBILE to your target board!

It has two modes of operation, namely AT command mode and Data communication mode. In AT command mode, we can configure the different control parameters which finally determine the working of the module. In this mode we can’t communicate with other devices. In Data communication mode, the device works as per the settings previously defined by the user in AT command mode and can communicates with other devices.

Hardware Features:

Typical -80dBm sensitivity
Up to +4dBm RF transmit power
Belongs to Bluetooth Class 2 category
UART interface with programmable baud rate
Built in integrated antenna
5Pin Standard Bergsrip
Power Supply: 3.3 - 5.5V
Breadboard Compatible
Onboard Status and Power LED
Support UART interface to host system
Speed:
- Asynchronous: 2.1Mbps(Max)/160 kbps
- Synchronous: 1Mbps/1Mbps
Security: Authentication and encryption
LED indications for indicating the connection status
User friendly operation
Key Selection Jumper
- Open: Command Mode
- Short: Data Mode

Software Features:

Default Baud rate: 38400, Data bits:8, Stop bit:1,Parity:No parity.
Supported baud rates: 9600, 19200, 38400, 57600, 115200, 230400 and 460800.
Given a rising pulse in PIO0, device will be disconnected.
Status instruction port PIO1: low-disconnected, high-connected;
When master and slave are paired, red and blue led blinks 1time/2s in interval, while disconnected only blue led blinks 2times/s.
Auto-connect to the last device on power as default.
Permit pairing device to connect as default.
Auto-pairing PINCODE: ”0000” as default
Pairing PINCODE: ”1234”as default

Documents:

We also recommend

Quickview

Bluetooth Mate Silver (Sparkfun USA)

Bluetooth Mate Silver is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. T..

Rs 1,949.00

Add to Cart

Add to Wish List Compare this Product

Buy Now Ask Question

Quickview

HC-05 Bluelink RS232 (rhydoLABZ)

Description: HC-05 is a low cost, easy to use Bluetooth module which communicates using RS-232 protocol. The device becomes ready to use by plugging i..

Rs 499.00

Add to Cart

Add to Wish List Compare this Product

Buy Now Ask Question

Quickview

Hc-05 Bluetooth Module with Base Board (chineese)

Hc-05 module is an easy to use Bluetooth module, designed for transparent wireless serial connection setup.It can be used in master or slave configura..

Rs 269.00

Add to Cart

Add to Wish List Compare this Product

Buy Now Ask Question

Quickview

Hc-06 Bluetooth Module with Base Board (chineese)

The Hc-06 is a Serial port Bluetooth module which having fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps Modulation with complete 2.4GHz..

Rs 299.00

Add to Cart

Add to Wish List Compare this Product

Buy Now Ask Question

Quickview

HC-08 Bluetooth Module

HC-08 Bluetooth Module is a new generation of Bluetooth specification V4.0 BLE Bluetooth protocol based on the transmission module. It works in the 2...

Rs 399.00

Add to Cart

Add to Wish List Compare this Product

Buy Now Ask Question

From the same brand

Quickview

28 Pin SSOP to DIP Adapter PCB - rhydoLABZ

This is a low cost SSOP to DIP Adapter (up to 28 pins) to convert the SSOP pins standard of 0.1" which is normally use in breadboards and donut boards..

Rs 40.00