Quectel EC200U series is a series of the latest LTE Cat 1 module optimized specially for M2M and IoT applications. It delivers maximum data rates up to 10 Mbps downlink and 5 Mbps uplink.EC200U series is compatible with Quectel multi-mode LTE Standard EC25 series / EC21 series / EC20 R2.1/ EC20..
This is a 4 Channel Isolated 5V 10A Relay Module Opto-coupler and Relay output maximum contact is AC250V 10A and DC30V 10A. This relay module features 4 x 5V relays rated at 10A/250V each. It is designed to switch up to 4 high currents (10A) or high voltage (250V) loads with the help of microcontrol..
The A2212/8T 1800KV BLDC Brushless Motor specifically made to power Quadcopters and Multirotors. This specific motor has 8 turns per pole and has a shaft speed of approximately 1800RPM/Volt. This Motor is equipped with the solid metal case which makes it reliable and durable. We recommend a minimum ..
This is 3.5 inch LCD Display for Raspberry Pi with 320 x 480 Resolution. This Display is lightweight and easy to install. This Screen comes with a stylus to interact with the small screen. The module sits right on top of Pi. This is ideal for DIY anywhere, anytime and does not require any separate p..
Dual SIM 4G LTE / 2G / GSM - Industrial Grade Modem OverviewThis is a Dual-SIM 4G LTE / 2G / GSM - Industrial Grade Modem Board , which is professionally designed with 4 layer Gold plated PCB having industrial grade protections. It is built with Multi-Band 4G LTE module, ..
Cellmeter-7 Digital Battery Capacity Checker is a simple and fast way to check battery voltage and condition of various type of battery within second. This capacitive tester will easily monitor battery cell voltages, total voltages, lowest cell voltage, highest cell voltage, gap between the highest ..
ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. To communicate with any STM8 or STM32 microcontroller located on an application board, the single-wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used...
This 4dBi high-performance 4G LTE PCB Flex Antenna is designed to provide reliable wireless connectivity in a compact form factor. It provides a strong and stable signal for data transmission and reception. It is built with a flexible printed circuit board (PCB) that allows it to conform to di..
HF49FD/005-1H11T is 5V 5A SPST NO-1A Miniature Power Relay. This relay's coil is rated up to 5V and the contacts are rated up to 5A (@250VAC, 30VDC).Specifications:Coil Voltage : 5VContact Material : AgSnO2Maximum Switching Voltage : 250V@ACOperating Tem..
The MCP23S17-E/SS is a 16-bit I/O expander with SPI interface from Microchip. It is a general purpose device that provides an easy way to add more I/O pins to a microcontroller. The device can be used to expand the number of I/O pins available on a microcontroller, allowing more complex control and ..
The M66 is a quad-band GSM/GPRS 2G module which uses LCC castellation packaging. Based on the latest 2G chip-set, it is optimized for data, SMS and audio transmission, and is designed for low-power IoT use cases that operate in harsh conditions.The M66 uses surface mounted technology, making it idea..
The PICkit 3.5 Offline Programmer/Debugger is designed with an easy-to-use interface for programming and debugging Microchip’s Flash families of microcontrollers. This PICkit 3.5 allows debugging and programming of PIC and dsPIC Flash microcontrollers using the powerful graphical user interface of t..
The MUP-C7801-2 is a Push-Push Nano Sim Card Connector. This sim card connector is without post or normally close type. This SIM card connector use Push-push mechanism to eject or insert the SIM card. The interface for sim card is a spring loaded push type.
The connector contains 7 pins for..