RFID Access Control Shield with 3LA - rhydoLABZ

(0) 0 out of 5 stars Write reviewReport bug
  • Part No :
  • RFID-2591
  • Availability:
  • In Stock
  • Shipping :
  • Same Day*
  • Weight:
  • 0.08Kg
  • Made By:
  • rhydoLABZ
  • Mfr.Part.No:
  • RFID-2591
  • Quality Rank:
  • 100/100
Rs 2499
(Excluding GST.)
Rs 2949
(Including GST)
2949 rhydoLABZ.com New In Stock
  • Buy & earn 250  reward points
  • GST Invoice & Input Credit Available
Quantity :
Description: This RFID Access Control Shield transforms your Arduino to an access control device. It comes with ID-3LA Reader Module presoldered on to the shield. This shield includes almost everything that an access control system requires. Onboard Relay driving circuitry helps your Arduino to control magnetic locks, solenoid valve etc. The 5V buzzer provided on board can be used for indicating the RFID card acceptance, say single beep for card acceptance and double beep for rejection.

Relay pins are available on a 3-pin screw terminal (NO,NC,COM) along with a 2-pin screw terminal for powering the 12V relay. Three LEDs are provided on board; STS, RLY and PWR. PWR indicates the power while RLY indicates relay actuation. STS comes in direct connection with  an Arduino pin (D12) and it can be controlled in accordance with your Arduino sketch.

The shield is provided with an on board DPDT sliding switch which helps you to connect the RFID module either to your PC (via Arduino USB) or to your Arduino itself. This feature helps you to configure/test the RFID module before actually using it in your project, this eliminates the need for any separate RFID development board. In addition there are two onboard switches enhancing its features. SW1 can be used to reset your arduino board. Whereas,  SW2 is a programmable switch that comes in connection with arduino pin (D10). Shield also comes with a couple of jumper connections for easy adaptation.

Jumper     Function
J1 Enables/Disables Buzzer
J2 TX Voltage Divider (short if used with 3V3 Arduino Boards)
J3,J4 Selects between hardware UART and software UART
J5 RX Voltage Divider  (short if used with 3V3 Arduino Boards)
J6 Switches Buzzer between Arduino & Module
J8 Output format selection (Serial ASCII: Strap to GND, WEIGAND 26: Strap to +5V)
Switching buzzer to module (using jumper J6) automatically triggers the buzzer whenever a RFID tag is read by the reader. The shield does come with headers pre-installed, just plug it and  your arduino is ready to read RFID tags. Do burn a proper sketch before trying to read any tags ;)

Note: If you are using multiple shields, make sure this shield stays on top of all others. ID-3LA requires external antenna, datasheet has detailed explanation on antenna design.

  • 125kHz read frequency
  • 20 to 30cm of reading distance
  • Compatible with all Arduino boards, mounts directly onto your Arduino
  • Professionally Designed Double sided FR-4 PTH PCB
  • On board ID - 3LA Reader Module, also supports μRFID, EM-18 and other modules with similar pinouts.
  • Onboard DPDT switch allows you to select the destination for RFID Output (PC or Arduino)
  • Onboard Relay with screw terminals for connection
  • Onboard Buzzer for Audio alert (could be switched between arduino/module via jumper)
  • Pinout for WIEGAND output
  • Manchester 64-bit, Modulus 64 Encoding
  • EM4001 64-bit RFID tag compatible
  • 9600bps TTL interface
  • Magnetic stripe emulation output
  • Operating Voltage: 2.8~5V DC
  • ID3LA I/O Output Current: +/- 200mA PK
  • Arduino Reset button brought out on shield for easy of accessibility.
  • Additional programmable switch in connection with arduino pin
  • 3 LEDS ,Power, Relay Status and a programmable LED in connection with arduino pin
  • Length: 62mm
  • Width: 54mm
  • Height: 12mm (excluding headers)
Package Includes:
  • 1 x RFID Access Control Shield with ID-3LA
  • 1 x Jumpers - 2.54mm
Sort by: Recently  /  Helpful Write review

There are currently no any reviews about this product.

There are currently no any question about this product.

Ask a question about RFID Access Control Shield with 3LA - rhydoLABZ

Report issue about the RFID Access Control Shield with 3LA - rhydoLABZ

Ask a question about the RFID Access Control Shield with 3LA - rhydoLABZ

Report issue about the RFID Access Control Shield with 3LA - rhydoLABZ

Request price match for the RFID Access Control Shield with 3LA - rhydoLABZ

Found this item with same quality and at a lower price but prefer to buy from rhydoLABZ.com?

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

RFID Access Control Shield with 3LA - rhydoLABZ