Description : This is the camera module for ARM 11(LS6410) Board. This uses the OV9650 camera sensor. The OV9650 Camera chip is a low voltage CMOS image sensors that provides the full functionality of a single-chip SXGA (1280x1024) camera and image processor in a small footprint package. The O..
Description: LS6410 CORE is an small size, low power, and high performance ARM11 core board. It can be used on car, home automation, industry PDA, industry digital control, consumer electronics, mobile terminal etc. Click here to check out other LS6410 related productsSpecifications:8 layer design. ..
Description: This IEEE 802.11 b/g Wireless LAN Module is the WiFi module used on LS6410 S3C6410 development board. Compliance with the IEEE 802.11b/g standard, it uses Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), DBPSK, DQPSK, CCK and QAM baseband modula..
Description: The Papilio One is an open-source development platform based on the capable Xilinx Spartan 3E FPGA. While FPGA devices are massively powerful and configurable, they haven’t always been the easiest to develop. Papilio attempts to remedy this situation by following the lead of popular mic..
Description: This product is compatible with IEE 802.11B / G standard, supports wireless transmission speed up to 54Mbps ie five times the normal 11b products, support 64/128 bits WEP data encryption, while supporting WPA / WPA-PSK.WPA2/WPA2-PSK security mechanism. Its external one omni-directional ..
Description: This is a breakout board for the ATmega128RFA1. It includes an on board 3.3V regulator, chip antenna, and DC input jack. The board can be powered with either a 5V or a 9V wall wart. ATmega128RFA1 is an IEEE 802.15.4 compliant single-chip, combining the industry- leading AVR microcontrol..
Description: WIZ-Embedded WebServer provides the tiny web server operating on low-speed MCU. It controls digital output or monitors digital and analogue input through web browser. The web page is stored in the serial flash memory of the board, and can be updated through network.
Features:
..
Description: This Evaluation Board for iMCU W7100A aids Quick Test of W7100A. iMCU W7100A is the one-chip solution which integrates an 8051 compatible micro-controller, 64KB SRAM and hardwired TCP/IP core for high performance and easy development. The TCP/IP core is a market-proven hardwired TCP/IP ..
Description: This is a Samsung S3C2440 micro contoller based system on module. It has 6-layer 70*50mm PCB, 2 x 4Banks x 4Mbits x 16bits (64MB) SDRAM, 256M Nandflash, 4MB NOR Flash, dual operating system (Both WinCE and Linux can be loaded at the same time)Specifications:CPU:Samsung S3C2440A-40..
The ATSAM3U ARM-CM3 Board (AT3U) is an ARM embedded evaluation board produced by Embest, integrate the ATMEL Cortex-M3 core-based processor ATSAM3U4E, operating at 96 MHz frequency. The board features USB, I2C, MCI interface, TFT-LCD, USART interface, 96 I/O port, EBI support SRAM/NOR/NAND memory, e..
Description: The ATMEL SAM9G45 Board (A9G4) produced by Embest is a full-featured evaluation board based on the ATMEL's new processor C AT91SAM9G45 which runs at up to 400MHz, with 128 Mbytes DDR2 memory and 256 Mbytes SLC NAND Flash. The board provides a wide range of peripherals, including a high-..
Description: This is the second generation development/prototype board for the MSP430F413 processor from Olimex. Comes with battery power supply circuit, buzzer, new specialized LCD display, crystal oscillator circuit, JTAG port, LEDs, 2 larger Buttons, RS232 interface, and extension ports. New and ..
The STM32F103ZE (SZE1) is an ARM evaluation board produced by Embest, integrate the STMicroelectronic ARM Cortex-M3 core-based processor STM32F103ZE, operating at a 72 MHz frequency. The board features USB, CAN, SD Card interface, TFT-LCD, RS232 serial interface, four 26-pin user extended interface,..
Description: The eDu LPC2138 is a NXP ARM7TDMI (16 & 32 bit) based LPC2138 microcontroller self study kit, suitable for teaching and learning embedded system programming. This tutorial is intended to give a detailed picture of programming the Philips (NXP) LPC2138 ARM7 microcontroller. The tutor..