PN532 NFC RFID module V3 is built around NXP PN532. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. This is al..
This Quad Band Wired Cellular Antenna is designed for GSM GPRS 900/1800MHz system of communication. This module comes with SMA connector and is 3 meter long.
Specifications:
Supply voltage: 3.3 ~ 5.0V DC
Cable length : 3m
Polarization: Linear polarization
Frequency range:
GSM850/900 : 80..
Humidity Temperature Sensor DHT22 is a calibrated digital temperature and humidity module with onboard sensor DHT22 (AM2302), which features higher accuracy and wider measuring range than DHT11. It can be used for detecting ambient temperature and humidity, through the standard single-wire interface..
This stepper motor is an electromechanical device which converts electrical pulses into discrete mechanical movements. The shaft or spindle of a stepper motor rotates in discrete step increments when electrical command pulses are applied to it in the proper sequence.This motor can be used with onboa..
Lipo Battery 4200mAh/11.1V has three cells and outputs 11.1V storing 4200mAh of charge.This is a good Li-po battery for projects like small robotics and radio-controlled projects. It has high discharge rates and big capacity and can be used in RC airplane, RC helicopter, RC car, RC truck, RC boat, ..
Lipo Battery 3000mAh / 11.1V has three cells and outputs 11.1V storing 3000mAh of charge.This is a good Li-po battery for projects like small robotics and radio-controlled projects. It has high discharge rates and big capacity and can be used in RC airplane, RC helicopter, RC car, RC truck, RC boat..
Lipo Battery 2200mAh / 11.1V has three cells and outputs 11.1V storing 2200mAh of charge.This is a good Li-po battery for projects like small robotics and radio-controlled projects. It has high discharge rates and big capacity and can be used in RC airplane, RC helicopter, RC car, RC truck, RC boat..
5" Touch Display for Raspberry Pi is HDMI LCD, which is a low-cost Resistive Touch Screen designed for Raspberry Pi. This 5" Resistive Touch Screen LCD enhances the UI experience in any project. It supports various systems such as Raspberry Pi, Banana Pi, Banana Pro, BeagleBone Black etc. The built ..
1.8 Inch Touch Display module have TFT LCD Screens (Thin-film-transistor liquid crystal display) are great graphical displays to display information. They are a variant of a liquid crystal display (LCD) which uses TFT technology to improve image qualities such as addressability and contrast. Since t..
BMP085 Barometric Pressure Sensor is a board with precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. The BMP085 is a high-precision, ultra-low power barometric pressure sensor. It offers a measuring range of 300 to 1100 hPa with an ab..
UFL connector male SMD is suitable for PCB layouts that require UFL antenna connections.
Specifications of UFL connector male SMD:
Main material: copper, the shell plating
Frequency range: 0 to 4 GHZ
The characteristic impedance: 50 Ω
The insulation resistance: 500 ..
This is a Case D SMD Tantalum Capacitor of 470uf capacitance with rated voltage 10V.
Specifications of 470uF Tantalum Capacitor 10V (CASE D):
Type: Tantalum Capacitor - Case D
Application: General Purpose
Package: 7343 SMD
Capacitance: 470uF
Rated Voltage: 10V
Operating Temperature: -55 °C..
This is a Case D SMD Tantalum Capacitor of 100uF capacitance with rated voltage 16V.
Specifications of 100uF Tantalum Capacitor 10% 16V (Case D)
Capacitance: 100uF
Rated voltage: 16V
Case code: D case
Capacitance tolerance: ±10%
Operating temperature range: -55°C to +125°C
Lead-free type
..
Copper Heatsink For Raspberry Pi can reduce chip temperature which prevent system failure. Copper Heat Sink for use with Raspberry Pi B. Help keep your Raspberry Pi cool, protect it from overheating. All Copper Heat Sinks come with thermal conductive tapes.
Specification of Copper Heatsink For Rasp..
MG90S Metal Gear Mini Servo is tiny and lightweight with high output power, this tiny servo is perfect for RC Airplane, Helicopter, Quadcopter or Robot. This servo has metal gear for added streangth and durabiliy. Servo can rotate approximately 180 degree(90 in each direction), and works just like t..