The S9V11F5S6CMA switching step-up/step-down regulator efficiently produces a fixed 5 V (default) or 6 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.) The regulat..
Dual G2 High-Power Motor Driver 24V14 are add-on boards for the Raspberry Pi, featuring pairs of discrete MOSFET H-bridges designed to drive two large brushed DC motors. They are designed to mount on and plug into compatible Raspberry Pi boards (Model B+ or newer), including the Pi 3 Model B and Mod..
The S9V11F3S5CMA switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that...
Pololu Dual G2 High-Power Motor Driver are add-on boards for the Raspberry Pi, featuring pairs of discrete MOSFET H-bridges designed to drive two large brushed DC motors. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 36 V operating range and are efficient enough to deliver a continuous ..
The S9V11MA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. ( Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.) The compact (0...
The S9V11F3S5C3 switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 3V to 16 V. The regulator also has fixed 3.3 V low-voltage cutoff with hysteresis that can be used ..
Altimu-10 V5 Gyro, Accelerometer, Compass, And Altimeter is a compact board that combines ST’s LSM6DS33 3-axis gyroscope and 3-axisaccelerometer, LIS3MDL 3-axis magnetometer, and LPS25H digital barometer to form an inertial measurement unit (IMU) and altimeter. These sensors are great ICs, but their..
The Romi Chassis Kit - Pink is a differential-drive mobile robot platform with a diameter of 6.5" (165 mm) and an integrated battery holder for six AA batteries (not included). The drive wheels are located on a diameter of the circular base plate, allowing for turns or spinning in place. A large, fi..
The Zumo Shield For Arduino, V1.2 is designed specifically to be a convenient interface between a Zumo chassis and an A-Star 32U4 Prime, Arduino Uno, or Arduino Leonardo. The shield mounts directly to the chassis, connecting to its battery terminals and motors, and the A-Star Prime or Arduino plugs ..
The Zumo reflectance sensor array provides an easy way to add line sensing or edge detection to a Zumo robot. It features six separate reflectance sensors, each consisting of an IR emitter coupled with a phototransistor that responds based on how much emitter light is reflected back to it. The two o..
Servo Extension Cable 12" Female - Female has JR connectors on both ends, so it can be used to make connections between devices with 0.1" 3-pin male headers, such as between RC servo controllers or RC receivers and motor controllers with an RC interface. The cable’s connectors are commonly found on..
Pololu 12V Step-Up Voltage Regulator U3V12F12 takes an input voltage as low as 2.5 V and efficiently boosts it to 12 V. The pins have a 0.1" spacing. Hence it is compatible with standard solderless breadboards and perfboards. They have a typical efficiency between 80% to 90%. The available output c..
Pololu 9V Step-Up Voltage Regulator U3V12F9 switching step-up (or boost) voltage regulator takes input voltage as low as 2.5 V and efficiently boosts to 9 V. The pins have a 0.1" spacing, making this board compatible with standard solderless breadboards and perfboards. They are switching regulators ..
Magnetic Encoder Disc For 20D Mm Metal Gearmotors, Od 9.7 Mm, Id 2.0 Mm, 20 Cpr (Bulk) can be used with 20D mm metal gearmotors (extended motor shaft versions only) as part of a quadrature encoder system that offers 20 counts per revolution. They are 2 mm thick with a 9.7 mm diameter, and the hole t..
Magnetic Encoder Pair Kit For 20D Mm Metal Gearmotors, 20 Cpr, 2.7-18V uses a magnetic disc and Hall effect sensors to provide 20 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or any o..