Description: Once you've hacked everything, why not go out in the garage and hack your car? This cable allows you to access the pins on your car's OBDII connector. It has an OBDII connector on one end and a DB9 female serial connector on the other. The overall length of the cable is 5'.
..
Description: The SparkFun Serial Enabled LCD Backpack allows you to control a
parallel based LCD over a single-wire serial interface. The SerLCD
backpack takes care of all the HD44780 commands allowing seamless
integration with any micro that can communicate over a wide range of TTL
serial baud ..
It's not what project you have in mind that may use a rocket launch switch... The question is what project will you come up with once you have one in hand? Everyone has a proverbial missile to launch.
The hot red safety cover protects a toggle switch from accidentally being turned on. When flipped ..
Description: The Joystick Shield kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino function..
Description: The Danger Shield mounts on top of your Arduino or Arduino Pro and equips it with a variety of fun and useful inputs and outputs. The Danger Shield has so much potential; we can't wait to see what you're able to do with it!
The shield's features include:
Three linear slide poten..
Description: You don’t have the power? Well, there’s no need to ask Scotty – the SparkFun Benchtop Power Board Kit has your back. This board will let you take advantage of your old (or new) power supply to create a benchtop power supply with enough juice to run almost any of your embedded elec..
Description: These are the nRF2401A 2.4GHz transceiver modules with built in chip antenna designed around the Nordic Semiconductor nRF2401A with high sensitivity and range. Units come with an empty 0.1" spaced footprint ready for a straight header, right angle header (recommended), or your own wires..
Description: The SparkFun Logomatic v2 takes everything we learned with multiple logging projects over the years and boils it down to an easy to use device, that is now more adaptable than ever! Version 2 incorporates the LPC2148 with microUSB, battery charging, FAT32 formatting, and microSD support..
Description: This is a very small infrared receiver based on the TSOP85 receiver. This receiver has all the filtering and 38kHz demodulation built into the unit. Simply point a IR remote at the receiver, hit a button, and you'll see a stream of 1s and 0s out of the data pin.
Features of TSOP85 re..
Description: This is a through-hole version of the popular surface mount Simon kit. This newer version comes with an ATmega328 instead of the ATmega168. All components are through-hole, making this kit great for beginners. When building this kit, you'll have a chance to solder a 28-pin microprocesso..
Description: 4-digit 7-segment displays are really neat little devices, it’s a shame that they can be so cumbersome to control. Well we’ve solved that problem by making them a little bit “smarter.” The SparkFun 7-Segment Serial Display combines a classic 4-digit 7-segment display and an ATMega328 mi..
Breakout Board for XBee Module is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing between 0.1" headers is 0.5" making it breadboard DIP friendly. We highly recommend using the f..
Description: Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin.
Package Includes:
1 x TEMT6000 Breakout Board
Documents:
..
Here is a simple 5 pack of yellow LEDs for LilyPad, or whatever else you can dream up. Light up the night!
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to all..
Description: Here is a simple 5 pack of green LEDs for LilyPad, or whatever else you can dream up. Light up the night!
LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting..