CC Debugger, LPC Debuggers & Programmers

(0) 0 out of 5 stars Write reviewReport bug
  • Part No :
  • TOL-3247
  • Availability:
  • Out of Stock
  • Shipping :
  • Same Day*
  • Weight:
  • 0.2Kg
  • Made By:
  • Waveshare
  • Mfr.Part.No:
  • 6799
Rs 2199
(Excluding GST.)
Rs 2595
(Including GST)
2595 rhydoLABZ.com New Out of Stock
  • Buy & earn 220  reward points
  • GST Invoice & Input Credit Available

The CC Debugger is primarily used for debugging and programming the flash on CCxxxx 8051-based System-on-Chip (SoC) devices from Texas Instruments. CC Debugger also supports CCxxxx RF transceivers. In addition, CC Debugger is used for configuring the CC85xx devices with PurePath Wireless Configurator.


Specifications of CC Debugger, LPC Debuggers & Programmers :

    Performance

  • Compatible with the original TI CC Debugger
  • Supported OSs:Windows 2000, Windows xp sp2/sp3, Windows Vista 32bit, Windows 7 32bit
  • Target voltage: 1.2V ~ 3.6V
  • Capable of powering the target board from the debugger
  • Operating temperature: 0~85 degree

    Supported Software

  • IAR Embedded Workbench For C8051
  • SmartRF Flash Programmer
  • SmartRF Studio
  • SmartRF Packet Sniffer
  • PurePath Wireless Configurator
  • Connects to PC

    Computer connection via USB interface

  • Connects to target board

          Target board connection via 10-pin IDC connector (2x5 2.54mm pitch). The figure below shows the header pinout:CC Debugger header pinout

CC Debugger header pinout

Supported Devices

    Programming and debugging the following 8051-based system-on-chips from Texas Instruments:
        CC1110, CC1111
        CC2430, CC2431
        CC2510, CC2511
        CC2530, CC2531, CC2533
        CC2540, CC2541
        CC2543, CC2544, CC2545
    Controlling the following transceivers from SmartRF Studio:
        CC1120, CC1121, CC1125, CC1175
        CC1101, CC110L, CC113L, CC115L
        CC2520
    Configuring the CC85xx devices with PurePath Wireless Configurator:
        CC8520, CC8521
        CC8530, CC8531

LED Status

    OFF: The debugger has no power or there is no valid firmware on the debugger.
    AMBER (BOTH LEDS ON): The debugger is powered, but there is no valid firmware.
    RED LED BLINKING: The Debugger is in Boot Recovery Mode.
    RED LED ON: No device detected.
    GREEN LED ON: The target device has been properly detected. It is possible to start programming/debugging.


Package includes:

  •     CC Debugger × 1
  •     USB cable × 1
  •     10-pin flat cable × 1

Resources :

 

Sort by: Recently  /  Helpful Write review

There are currently no any reviews about this product.

There are currently no any question about this product.

Ask a question about CC Debugger, LPC Debuggers & Programmers

Report issue about the CC Debugger, LPC Debuggers & Programmers



Ask a question about the CC Debugger, LPC Debuggers & Programmers

Report issue about the CC Debugger, LPC Debuggers & Programmers



Request price match for the CC Debugger, LPC Debuggers & Programmers

Found this item with same quality and at a lower price but prefer to buy from rhydoLABZ.com?

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

CC Debugger, LPC Debuggers & Programmers