Menu
Your Cart
Dear Valued Customers: We're excited to announce our move to a new website!  Existing Customers, kindly utilize the 'Forgot Password' option to update the Password. Thank you for your cooperation!

TB67S128FTG Stepper Motor Driver Carrier - Pololu USA

TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
TB67S128FTG Stepper Motor Driver Carrier - Pololu USA
  • Stock: In Stock
  • Brand: Pololu - USA
  • Model: MOT-3239
  • Weight: 0.10kg
  • MPN: 2998
Rs 999

This breakout board makes it easy to use Toshiba’s TB67S128FTG microstepping bipolar stepper motor driver, which features adjustable current limiting and microstepping down to 1/128-step. In addition, it has the ability to dynamically select an optimal decay mode by monitoring the actual motor current, and it can automatically reduce the driving current below the full amount when the motor is lightly loaded to minimize power consumption and heat generation. The driver has a wide operating voltage range of 6.5 V to 44 V and can deliver approximately 2.1 A per phase continuously without a heat sink or forced air flow (up to 5 A peak). It features built-in protection against under-voltage, over-current, and over-temperature conditions. Carrier board also adds reverse-voltage protection (up to 40 V).

Features:

  • Two interface modes to select from:
    • Clock mode for simple step and direction control
    • Serial mode for controlling the driver’s many features through a serial interface (this mode also allows for serial control of the current limit)
  • Eight different step modes: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, 1/32-step, 1/64-step, and 1/128-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • Four different decay modes: mixed decay (two timing ratios), fast decay, or Advanced Dynamic Mixed Decay (ADMD), which dynamically switches between slow and fast decay modes by monitoring the state of current decay (not according to fixed timing)
  • Configurable Active Gain Control (AGC) automatically reduces drive current to minimize power consumption and heat generation when maximum torque is not needed
  • Motor supply voltage: 6.5 V to 44 V
  • Can deliver up to approximately 2.1 A per phase continuously (5 A peak) without additional cooling
  • Can interface directly with 3.3 V and 5 V systems
  • Protection against over-current/short-circuit and over-temperature
  • Open-load detection
  • Active-low error outputs indicate over-current, over-temperature, or open-load condition
  • Carrier board adds reverse-voltage protection up to 40 V
  • Carrier board breaks out all of the TB67S128FTG pins in a compact size (1.2 inch × 1.6 inch)
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

Specifications: 

  • Motor driver: TB67S128FTG
  • Minimum operating voltage: 6.5 V
  • Maximum operating voltage: 44 V
  • Continuous current per phase: 2.1 A
  • Maximum current per phase: 5.0 A
  • Minimum logic voltage: 2 V (This is the input logic high threshold)
  • Maximum logic voltage: 5.5 V
  • Microstep resolutions:  full, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128
  • Current limit control: potentiometer, digital, SPI-programmable
  • Reverse voltage protection: Yes (Note: Reverse voltage protection only works up to 40 V)
  • Header pins soldered: No

Using the driver

Package Includes:

  • 1x TB67S128FTG Stepper Motor Driver Carrier board
  • 2× 16-pin breakaway 0.1inch male header strips
  • 3x  2-pin, 3.5 mm terminal blocks (for board power and motor outputs)
  • 1x  0.1inch shorting block (for optionally connecting IOREF to the neighboring VCC pin when using this driver in 5 V systems)

Documents / Downloads:

Write a review

Please login or register to review