ARM7 Stick - LPC2138 - rhydoLABZ

(4) 4.5 out of 5 stars Write reviewReport bug
  • Part No :
  • QSB-2196
  • Availability:
  • In Stock
  • Shipping :
  • Same Day*
  • Weight:
  • 0.1Kg
  • Made By:
  • rhydoLABZ
  • Mfr.Part.No:
  • QSB-2196
  • Quality Rank:
  • 100/100
Rs 2999
(Excluding GST.)
Rs 3539
(Including GST)
3539 New In Stock
  • Buy & earn 300  reward points
  • GST Invoice & Input Credit Available
Quantity :
Description: The Stick Series quick start boards from rhydoLABZ are primarily intended to be used as a development system for 64-pin ARM Controllers (LPC2129/38/48), which can also be used as stand-alone devices. Over the last few years, the ARM architecture has become the most pervasive 32-bitarchitecture in the world of embedded electronics while LPC2148/38/29 still being the most widely used in ARM7 family. They come with many inbuilt peripherals making them more efficient and a reliable option for the beginners as well as high end application developers.

rhydoLABZ LPC2138 Stick consists of all basic components required to quickly evaluate and demonstrate the capabilities of NXP LPC2138 (ARM7TDMI) microcontroller. LPC2138 is an ARM7TDMI-S based high-performance 32-bit RISC Microcontroller with Thumb extensions 512KB on-chip Flash ROM with In-System Programming (ISP) and In-Application Programming (IAP), Two 8-ch 10bit ADC 32KB RAM, Vectored Interrupt Controller, Two UARTs, one with full modem interface. Two I2C serial interfaces, Two SPI serial interfaces Two 32-bit timers, Watchdog Timer, Real Time Clock with optional battery backup, Brown out detect circuit, General purpose I/O pins. CPU clock up to 60 MHz, On-chip crystal oscillator and On-chip PLL.

The Stick board is designed and populated with USB connector, voltage regulator, RTC crystal, Main Crystal and necessary de-coupling capacitors in a breadboard friendly form factor with access to all Port pins for external connection. The voltage regulation circuitry of the stick is designed with LD1117 regulator that provides a stable 3V3 for the controller. Power supply input can be either from the VCC pinout or the USB Supply (Use J1 for appropriate power input selection). The design also includes a reset switch to avoid programming pitfalls and to manually bring back the system to the initialization mode. LPC2138 can be programmed within the system using Stick's USB interface.

NOTE: The LPC2138 Stick comes with pre-programmed bootloader, can be programmed using USB-UART interface available on-board. Also, the board can be powered using the same USB connector.

NOTE: Form-factor & pin-out our ARM Stick Quick-start boards are entirely different from that of our ARM header boards.

Stick Features:
  • Breadboard friendly design
  • On board USB to Serial converter
  • Can be powered externally or via USB
  • Onboard LDO regulator for 3V3 Supply
  • On board LPC2138 loaded with bootloader code
  • Access to all Port pins for external connection
  • Push button to hardware reset the controller
  • Automatic ISP entry mode (via Jumpers - J4 & J5)
  • 12MHz Crystal for system clock and 32kHz Crystal for onchip RTC
  • USB interface for Serial communication and Programming
  • JTAG connector with 2x5 pin layout for programming/debugging
  • Programmable via USB interface and JTAG interface
  • RTC battery backup pins brought out via protection diodes
  • Professionally designed High Quality PTH PCB
  • Power Indication LED
LPC2138 Key Features:
  • 16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.
  • 32 kB of on-chip static RAM and 256/512 kB of on-chip Flash program memory. 128 bit wide interface/accelerator enables high speed 60 MHz operation.
  • In-System/In-Application Programming (ISP/IAP) via on-chip boot-loader software. Single Flash sector or full chip erase in 400 ms and programming of 256 bytes in 1 ms.
  • EmbeddedICE RT and Embedded Trace interfaces offer real-time debugging with the on-chip RealMonitor software and high speed tracing of instruction execution.
  • Low power Real-time clock with independent power and dedicated 32 kHz clock input.
  • CPU operating voltage range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads
  • Input Voltage: 4.5V ~ 6.5V
  • Recommended Voltage input: 5V
  • Current Draw: 500mA @5V
  • Dimensions: 64.5 x 31.5 MM
Package Includes:
  • 1x LPC2138 Stick
  • 4x Jumper

NOTE: Stick needs a micro USB cable and a JTAG ribbon cable to program and debug the controller, which is not included in this package. You could have the micro USB cable for yourself from here.

Sort by: Recently  /  Helpful Write review


By ramkumar from N/A on June 28, 2016
good product ,compact size and cheap rate ,helped for my academic projects.
Was this review helpful to you?   Yes   No

good product

By maheswara gupta from N/A on June 28, 2016
excellent work, can be programmed using USB,easy to use also board can be powered using the same USB connector. excellent work from rhydolabz
Was this review helpful to you?   Yes   No

By Aravind Nadal from N/A on February 05, 2016
An Arduino form factor would have been greatly appreciated. This would have definitely increased its flexibility.
Was this review helpful to you?   Yes   No

By Aravind Nadal from N/A on February 05, 2016
Sweet!!! Cheep & good quality board. This is what I was looking for.
Was this review helpful to you?   Yes   No

There are currently no any question about this product.

Ask a question about ARM7 Stick - LPC2138 - rhydoLABZ

Report issue about the ARM7 Stick - LPC2138 - rhydoLABZ

Ask a question about the ARM7 Stick - LPC2138 - rhydoLABZ

Report issue about the ARM7 Stick - LPC2138 - rhydoLABZ

Request price match for the ARM7 Stick - LPC2138 - rhydoLABZ

Found this item with same quality and at a lower price but prefer to buy from

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

ARM7 Stick - LPC2138 - rhydoLABZ