ARM7 Stick - LPC2129 - rhydoLABZ

(2) 5 out of 5 stars Report bug

Part No :
QSB-2195
Availability:
In Stock
Shipping :
Same Day*
Weight:
0.1Kg
Made By:
rhydoLABZ
Mfr.Part.No:
QSB-2195
Quality Rank:
100/100

Rs 3999

(Excluding GST.)

Rs 4719

(Including GST)

Buy & earn 400 reward points
GST Invoice & Input Credit Available

Quantity :

Got Better Price

Description: The Stick Series quick start boards from rhydoLABZ are primarily intended to be used as a development system for 64-pin ARM Controllers (LPC2129/38/48), which can also be used as stand-alone devices. Over the last few years, the ARM architecture has become the most pervasive 32-bit architecture in the world of embedded electronics while LPC2148/38/29 still being the most widely used in ARM7 family. They come with many inbuilt peripherals making them more efficient and a reliable option for the beginners as well as high end application developers.

rhydoLABZ LPC2129 Stick consists of all basic components required to quickly evaluate and demonstrate the capabilities of NXP LPC2129 (ARM7TDMI) microcontroller. LPC2129 is an ARM7TDMI-S based high-performance 32-bit RISC Microcontroller with Thumb extensions 256KB on-chip Flash ROM with In-System Programming (ISP) and In-Application Programming (IAP) 16KB RAM, Vectored Interrupt Controller, Two UARTs, I2C serial interface, 2 SPI serial interfaces Two timers (7 capture/compare channels), PWM unit with up to 6 PWM outputs, 4-channels 10bit ADC, 2 CAN channels. Real Time Clock, Watchdog Timer, General purpose I/O pins. CPU clock up to 60 MHz, On-chip crystal oscillator and On-chip PLL.

The Stick board is designed and populated with USB connector, voltage regulators, 10MHz Crystal and necessary de-coupling capacitors in a breadboard compatible formfactor with access to all Port pins for external connection. The voltage regulation circuitry is based on two ICs; an LD1117 LDO regulator generating 3V3 input power supply and a CP2985 generating 1V8 for the processor CPU. Power supply input can be either from the VCC pinout or the USB Supply (Use J1 for appropriate power input selection). The design also includes a reset switch to avoid programming pitfalls and to manually bring back the system to the initialization mode. LPC2129 can be programmed within the system using Stick's USB interface.

NOTE: The LPC2129 Stick comes with pre-programmed bootloader, can be programmed using USB-UART interface available on-board. Also, the board can be powered using the same USB connector.

NOTE: Form-factor & pin-out our ARM Stick Quick-start boards are entirely different from that of our ARM header boards.

Stick Features:

Breadboard Compatible design
On board USB to Serial converter
Can be powered externally or via USB
Onboard regulators for 3V3, 1V8 regulation
10MHz Crystal for system clock
On board LPC2129 loaded with bootloader code
Access to all Port pins for external connection
Push button to hardware reset the controller
Automatic ISP entry mode (via Jumpers - J4 & J5)
USB interface for Serial communication and Programming
JTAG connector with 2x5 pin layout for programming/debugging
Programmable via USB interface and JTAG interface
Professionally designed High Quality PTH PCB
Power Indication LED

LPC2129 Key Features:

16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.
16 kB on-chip Static RAM, 128/256 kB on-chip Flash Program Memory. 128-bit wide interface/accelerator enables high speed 60 MHz operation.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip boot-loader software. Flash programming takes 1 ms per 512 byte line. Single sector or full chip erase takes 400 ms.
EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service routines can continue to execute while the foreground task is debugged with the on-chip RealMonitor“ software.
Embedded Trace Macrocell enables non-intrusive high speed real-time tracing of instruction execution.
CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).
I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.

Specification:

Input Voltage: 4.5V ~ 6.5V
Recommended Voltage input: 5V
Current Draw: 500mA @5V
Dimensions: 64.5 x 31.5 MM

Package Includes:

1x LPC2129 Stick
4x Jumper

Downloads:

NOTE: Stick needs a micro USB cable and a JTAG ribbon cable to program and bug the controller, which is not included in this package. You could have the micro USB cable for yourself from here.

Displaying 1 to 2 (of 2 reviews)

Sort by: Recently / Helpful

USB connectivity is great

By SuSu from Kerala, India on July 02, 2016

Its much better that the previous board

Was this review helpful to you? Yes No

Stick is a real good thing

By Nilesh from Perak, Malasia on April 20, 2016

To get started and to work on with the ARM7 LPC2129 controllers stick is the best option i dont find anything else like this

Was this review helpful to you? Yes No

Displaying 1 to 2 (of 2 reviews)

- Q
- Can we upload code via USB?
  asked by Alen Thomas on April 23, 2016
- A
- Yes, the code can be uploaded via USB
- Q
- Hi
  Yesterday i have purchased 2-LPC2129 stick boards, i have installed USB to uart CP210x drivers.I tried to flash using Flash Magic, i have an issue with this and i am not able to flash it.Help me in this regard,
  Error is unable to communicate.
  
  Thank you.
  asked by KS Subramanya Kasyao on April 16, 2018
- A
- The important steps are done before communicating with ARM stick.
  firstly install USB to uart CP210x driver and check the COM port in device manager and select the same COM port in flash magic .Place the jumper in appropriate position (RST and ISP).

Request price match for the ARM7 Stick - LPC2129 - rhydoLABZ

Found this item with same quality and at a lower price but prefer to buy from rhydoLABZ.com?

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.