Description: The all New PIC18F4580 Development Board-Mini can be used to evaluate and demonstrate the capabilities of PIC18F4580 microcontrollers and CAN Communication. Since all I/O pins are brocken out on Male and female Berg strips, it is very easy to use for development purpose as well. The board is designed for general purpose applications and it includes a variety of hardware to exercise microcontroller peripherals.
Onboard Mini Bread board is provided to ease the use,Ideally suitable for training and development purposes. Apart from this there is an onboard 2mm pitch Female sockets on both bottom and top side to insert Xbee module as per convenience. Since there are different modules (GPSBee, Bluebee, RFBee Etc) are available in the XBEE form factor, it will be easy to interface and experiment all of them.
The board is populated with MCP2552 CAN transceiver ic and related components to enable the CAN Communication. The CAN pins are available at a 4pin RMC connector with VCC and ground .Onboad 5v to 3v3 MOSFET based level converter and 3V3 Voltage regulator provide safe interface to XBEE and other low voltage devices .The onboard 5V regulator is having current rating of 1A and 3V3 voltage regulator is having 500ma capacity to easily power almost all onboard devices as well as external devices .All I/O pins and Power pins ( 5V & 3V3) are made available at Female header pins around the Breadboard to ease the wiring .Apart from this the All I/O pins are ready at male berg strips in two rows under the LCD. The UART pins are available at separate RMC Connector with power ( VCC & GND). a 3v3UART is provided with the help of onboard MOSFET voltage level converter.
The onboard mini-B type USB connector can be used to power the board as well as to communicates with PC. A jumper is provided to select the PC interfacing method ( USB or RS232).The development board can be programed by internal boot-loader or ICSP Programmer.A 6 PIN male connector and RJ11 Female connector has been provided to connect ICSP Programmer/Debugger. .Apart from USB the board has two more powering options like DC Adapter jack and 2Pin RMC connector with Reverse polarity protection. Available onboard peripheral interfaces are 3 nos Pull-up switches, 2 nos LEDs, buzzer, Analog Temp sensor, Analog POT,16X2 LCD,RS232,USB,CAN,Voltage Level Converter and connectors for xbee, sockets for RFID Module ( EM18 or uRFID) , SERVO Motor,UART etc.
All these peripheral interfaces can be disconnected by removing onboard PCB jumpers to free up the I/O PINS for other purposes.
Features:
- Includes PIC18F4580 Microcontroller
- Compact and Ready to use design
- Professional EMI/RFI Complaint PCB Layout Design for Noise Reduction
- High Quality Two layer PTH PCB
- No separate programmer required (On-Chip Boot loader)
- No Separate power adapter required (USB power source)
- RS-232 Interface (For direct connection to PC’s Serial port)
- USB Interface to connect to PC
- On Board Mini Breadboard for experiments
- On Board Two Line LCD Display (2x16)
- POT for LCD Contrast controlling
- On Board 3 LED Interface to test Port pin (with jumper select option)
- On Board Analog Pot interface to ADC (with jumper select option)
- On Board Analog Temperature Sensor Interface
- On Board Buzzer Interface
- On Board 3 button Pull-up Keyboard interface
- On Board 3.3V Regulator
- On Board Reset Switch
- On Board Connector for SERVO Output
- On Board Connector to interface Xbee module on top/bottom side
- On Board Connector to interface EM-18 compatible µRFID Reader module on top side
- On Board CAN transceiver IC
- On Board Power LED Indicator
- Adaptor (any standard 9-12V power supply) option
- All Port Pins available at Male Berge Strip
- All Port Pins available at FeMale Berge Strip around Bread board
- On Board ICSP & RJ11 Connector for Debugging/Programming
- Power Supply Reverse Polarity Protection
- On Board DB9 Connector (for UART)
- On Board USB Connector (for POWER/UART)
- On Board 4 pin RMC Connector (for UART)
- On Board 2 pin RMC Connector (for CAN)
- On Board 1 Amp Voltage Regulator
- On Board regulated 3V3 output
- On Board regulated 5V output
- Can be used as main board for developing applications
- On Board 20 MHz Crystal Oscillator
PIC18F4580 Chip Specification:
- Microchip PIC 18F4580 with 20 MHz Crystal Oscillator (With Boot loader Software)
- Built-in CAN Peripheral
- High Performance RISC CPU
- 32 KB Programmable Flash Memory
- 1536 bytes Data Memory (SRAM)
- 256 bytes EEPROM
- Supports Up to 40 MHz Operation
- 36 I/O pins
- 11-Channel 10-bit Analog to Digital Converter(ADC)
- One Capture module/ Compare Module/PWM Module
- One Enhanced Capture Module/ Compare Module/ PWM module
- One ECAN Module with Message bit rates up to 1 Mbps
- Parallel Communications (PSP) Support
- One 8-Bit Timer/Counter and Three 16-Bit Timer/Counter
- One Enhanced USART (Supports RS-232, RS-485 and LIN 1.3)
- One Master Synchronous Serial Port (MSSP)
- One Serial Peripheral Interface(SPI) Module
- One Inter-Integrated Circuit (I2C) Module
- Power-On Reset (POR), Power-Up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Interrupt Capability (up to 20 sources)
- Three External Interrupts
- In-Circuit Serial Programming (ICSP) via two pins
- In-Circuit Debug (ICD) via two pins
- Self Programmable under software control
- Programmable Brown Out Reset
- Low Voltage Programming
- Power Saving Sleep Mode
- Extended WatchDog Timer(WDT)
- Wide Operating Voltage 2.0V to 5.5V
- Low Power Consumption using nanoWatt Technology
Package Includes:
There are currently no any question about this product.
