Description: The eCee LPC2129 Development Board can be used to evaluate and demonstrate the capabilities of NXP LPC2129 microcontrollers. The board is designed for general purpose applications and includes a variety of hardware to exercise microcontroller peripherals. Ideally suitable for training and development purposes.
eCee LPC2129 Development Board Features
- Includes Base board + Header Board
- Compact and Ready to use design
- Professional EMI/RFI Complaint PCB Layout Design for Noise Reduction
- High Quality Two layer PTH PCB
Base Board Features
- Supports LPC2132/38/48 Header Boards
- Includes LPC2129 Header Board with in-built CAN Module
- No separate programmer required (On-Chip Boot loader)
- No Separate power adapter required (USB power source)
- Two RS-232 Interfaces (For direct connection to PC’s Serial port)
- On Board Two Line LCD Display (2x16) (with jumper select option)
- On Board 8 LED Interface to test Port pin (with jumper select option)
- On Board Pot interface to ADC
- On Board Temperature Sensor Interface
- On Board Buzzer Interface
- On Board 4x4 (16 Keys) Matrix Keyboard
- On Board I2C EEPROM
- On Board External Interrupt Button
- On Board Connector for PWM Output
- PWM controlled LCD backlight
- On Board Connector for AnalogOutput
- On Board Speaker Output
- LF Amplifier LM 386
- Adaptor (any standard 9-12V power supply) option
- On Board Power LED Indicator
- On Board Reset button
- All Port Pins available at Berg Strip
- On Board JTAG Connector for Debugging/Programming
- Power Supply Reverse Polarity Protection
- Three On Board DB9 Connectors (Two for UART and One for CAN)
- On Board USB Connector
- On Board 1 Amp Voltage Regulator
- On Board Connector for regulated 3V3 output
- On Board Connector for regulated 5V output
- Controller Area Network (CAN) transceiver
- Can be used as main board for developing applications
Header Board Features
- Easy to use DIP Package
- Includes NXP LPC 2129 Microcontroller with in-built CAN Module
- On Board Power LED Indicator
- On Board JTAG Jumper
- On Board 10 MHz Crystal Oscillator
- On Board 3.3V Regulator
- On Board 1.8V Regulator
- On Board Power Supply de-coupling Capacitors
- All Port Pins available at Berg Strip
- Header Module can be removed for developing your circuit
LPC 2129 Chip Specification
- NXP LPC 2129 with 10 MHz Crystal Oscillator (With Boot loader Software)
- High Performance 32-bit ARM7TDMI-S™ CPU
- 256 KB Programmable Flash Memory provides a minimum of 100,000 erase/write cycles and 20 years of data retention.
- 16 KB Data Memory (SRAM)
- In-System/In-Application Programming (ISP/IAP) via on-chip boot-loader software.
- Flash programming takes 1 ms per 512 byte line. Single sector or full chip erase takes 400ms.
- Embedded ICE-RT interface enables breakpoints and watch points.
- Two interconnected CAN interfaces with advanced acceptance filters
- Four channel 10-bit A/D converter with conversion time as low as 2.44 us.
- Multiple serial interfaces including two UARTs , Fast I2C (400 kbits/s) and two zPIs
- 60MHz maximum CPU clock available from programmable on-chip Phase-Locked Loop
- Vectored Interrupt Controller with configurable priorities
- Two 32-bit Timers.
- Four Capture and four Compare channels.
- PWM unit with six output pins.
- Watch Dog Timer
- Up to forty-six 5V tolerant general purpose I/O pins.
- Up to nine edge or level sensitive external interrupt pins.
- On-chip crystal oscillator with an operating range of 1MHz to 30MHz.
- Two low power modes - Idle and Power-down.
- Processor wake-up from Power-down mode via external interrupt.
- Individual enable/disable of peripheral functions for power optimization.
- CPU operating voltage range of 1.65V to 1.95V and I/O power supply range of 3.0V to 3.6V
eCee LPC2129 Package Includes
Downloads
- User Manual
- Datasheets
- Schematic
- Softwares
There are currently no any question about this product.
