User Interface Shield With 0.96 Inch SPI OLED Display Module

(3) 5 out of 5 stars Write reviewReport bug
  • Part No :
  • INT-2576
  • Availability:
  • In Stock
  • Shipping :
  • Same Day*
  • Weight:
  • 0.075Kg
  • Made By:
  • rhydoLABZ
  • Mfr.Part.No:
  • INT-2576
  • Quality Rank:
  • 100/100
Rs 699
(Excluding GST.)
Rs 825
(Including GST)
825 New In Stock
  • Buy & earn 70  reward points
  • GST Invoice & Input Credit Available
Quantity :

The rhydoLABZ UI Shield provides an easy way of interfacing OLED display modules with your Arduino boards. It features a monochrome OLED (0.96") display module, along with 5 keypad pins and few other added features. The 4 directional buttons plus select button allows basic control input. This feature packed shield, coupled with convenient display module, makes an ideal platform to build a stand-alone project with its own user interface.

The communication interface between the OLED display and the controller is via hardware SPI pins of the Arduino. Both the DC and CS signals of the display module are jumpered on the shield PCB for easy hardware configuration. Reset pin (RES) of the OLED module comes in connection with D10 of the Arduino. DC signal determines whether the transferred data is written to display data RAM or command register. You could use the SPI library provided under the resources tab below to display alphabets, numbers, symbols, images and anything once you know to handle the pixels.

Additionally the shield also supports standard character display (16x2). A character display can be used in 4 bit mode saving a few of your output pins, a contrast adjustment trim-pot is also provided for the same. Apart from the display interfacing, it has input switches, on board buzzer and LEDs. Shield uses the digital pins D8 to D13 for LCD interfacing, D3 toD7 for keypad buttons and D2 for buzzer. Analog pins A2, A3 and A4 are connected with LEDs, A0 comes in connection with a preset; put to use the ADC functionality. Arduino reset switch is brought out on the shied for easy accessibility.

This product comes as a kit! Includes high quality PTH PCB, 0.96" OLED display and other onboard features (buttons, buzzer, header etc). Most of the connections are jumper selective which makes it apt for prototyping as well. Ultimately rhydoLABZ UI shield is the super slick way to add a display without all the wiring hassle on your Arduino.

NOTE: The images sport out 1.3" monochrome OLED display, but the shield actually accompanies 0.96" monochrome OLED display.


  • Operating Voltage: 5V
  • Comes with a 0.96" OLED Display
  • 5 Momentary switches for custom menu control panel
  • RST button for resetting arduino program
  • Supports OLED Display (0.96" and 1.3") , SPI interfacing
  • Supports 16x2 Character display, 4bit mode
  • Trimmer resistor for varying analog input
  • On board buzzer for audio alert
  • Plug and play with any Arduino
  • Mounting support for display modules
  • Professionally Designed High Quality PTH PCB
  • Dimensions: 81.4x53.5 (MM)

OLED Display Specification:

  • OLED Driver IC: SSD1306
  • Display Pixel Color: Blue
  • Resolution: 128 x 64
  • Visual Angle: >160°
  • Compatible I/O Level: 3.3V, 5V
  • Mini Size: 2.7 x 2.8 (CM)

Jumper Connections:

Jumper Description
J1 Enables/Disables 'Left' Switch
J2 Enables/Disables 'Down' Switch
J3 Enables/Disables 'Select' Switch
J4 Enables/Disables 'Up' Switch
J5 Enables/Disables 'Right' Switch
J6 Enables/Disables 'LED3'
J7 Enables/Disables 'LED2'
J8 Enables/Disables 'LED1'
J9 Enables/Disables Buzzer
J10 Configures DC pin of the OLED Display
J11 Configures CS pin of the OLED Display
J12 Enables/Disables analog input on A0

Pins Used:

Pin Description
A0 Analog Input Pin connected to Preset
A2 Connected to LED, LED1
A3 Connected to LED, LED2
A4 Connected to LED, LED3
D2 Connected to Buzzer
D3 Connected to Switch, SW5
D4 Connected to Switch, SW4
D5 Connected to Switch, SW3
D6 Connected to Switch, SW2
D7 Connected to Switch, SW1
D8 Connected to OLED Pin, D/C
D9 Connected to OLED Pin, CS
D10 Connected to OLED Pin, RES
D11 Connected to OLED Pin, SDA
D13 Connected to OLED Pin, SCK
RES is the reset signal input pin. When this pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD)  during normal operation. CS is the chip select input pin (active LOW). Data/Command control is done over the D/C pin; when it is pulled HIGH (i.e. connect to VDD), the input data is treated as data. When it is pulled LOW, the input data will be transferred to the command register. SDA and SCK are the data and clock pins, respectively, used for communication with the controller.

Package Includes:

  • 1 x  User Interface Shield
  • 1 x  0.96" OLED Display Module
  • 9 x  Jumpers - 2.54mm


Sort by: Recently  /  Helpful Write review

Thank you!

By Bharat from Bengaluru, India on May 05, 2016
Thank you very much for the User LCD shield link.
Now the LCD is working fine.

Please update the same link in your product page also (small suggestion)
0 of 1 people found this review helpful
Was this review helpful to you?   Yes   No

By Ajay K S from N/A on January 29, 2016
Cool Stuff... good service from rhydolabz! Thankyou.....
Was this review helpful to you?   Yes   No

By Abraham John from N/A on December 23, 2015
I have used this shield with my arduino mega. It's working great. Thank you guys
Was this review helpful to you?   Yes   No

There are currently no any question about this product.

Ask a question about User Interface Shield With 0.96 Inch SPI OLED Display Module

Report issue about the User Interface Shield With 0.96 Inch SPI OLED Display Module

Ask a question about the User Interface Shield With 0.96 Inch SPI OLED Display Module

Report issue about the User Interface Shield With 0.96 Inch SPI OLED Display Module

Request price match for the User Interface Shield With 0.96 Inch SPI OLED Display Module

Found this item with same quality and at a lower price but prefer to buy from

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

User Interface Shield With 0.96 Inch SPI OLED Display Module