Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)

(1) 5 out of 5 stars Write reviewReport bug
  • Part No :
  • ARD-1948
  • Availability:
  • Out of Stock
  • Shipping :
  • Same Day*
  • Weight:
  • 0.1Kg
  • Made By:
  • Arduino - Italy
  • Mfr.Part.No:
  • A000068
  • Quality Rank:
  • 100/100
Rs 2999
(Excluding GST.)
Rs 3539
(Including GST)
3539 rhydoLABZ.com New Out of Stock
  • Buy & earn 300  reward points
  • GST Invoice & Input Credit Available
Qty Discount Price (Excl.GST)
1-4 Rs 2999
5-24 Rs 2939
25-49 Rs 2849
50-99 Rs 2789
100+ Rs 2699
Notify Me !

The Arduino Ethernet is a microcontroller board based on the ATmega328. It has 14 digital input/output pins, 6 analog inputs, a 16 MHz crystal oscillator, a RJ45 connection, a power jack, an ICSP header, and a reset button. An optional Power over Ethernet module can be added to the board as well.

The Ethernet differs from other boards in that it does not have an onboard USB-to-serial driver chip, but has a Wiznet Ethernet interface. This is the same interface found on the Ethernet shield. An onboard microSD card reader, which can be used to store files for serving over the network, is accessible through the SD Library. Pin 10 is reserved for the Wiznet interface, SS for the SD card is on Pin 4.

The Revision 3 of the board introduces the standardized 1.0 pinout, that consist in:

  • added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, this will the opportunity to shield that use i2c or TWI components to be compatible with all the Arduino boards;

  • the IOREF that allow the shields to adapt to the voltage provided from the board. Shields that use the IOREF pin will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V. Next to the IOREF pin there is a not connected pin, that is reserved for future purposes

The 6-pin serial programming header is compatible with the FTDI USB cables or USB-to-serial breakout boards. It features support for automatic reset, allowing sketches to be uploaded without pressing the reset button on the board. When plugged into a USB to Serial adapter, the Arduino Ethernet is powered from the adapter.

Note:

  • USB connection is off-board, we strongly recommend using a (USB to Serial Converter + USB miniB Cable)

  • Pins 10, 11, 12 and 13 are reserved for interfacing with the Ethernet module and should not be used otherwise. This reduces the number of available pins to 9, with 4 available as PWM outputs.

NOTE: This is 100% GENUINE ARDUINO board.

Arduino Ethernet Features:

  • Microcontroller: ATmega328
  • Operating Voltage 5V
  • Input Voltage Plug (recommended) 7-12V
  • Input Voltage Plug (limits) 6-20V
  • Input Voltage PoE (limits) 36-57V
  • Digital I/O Pins 14 (of which 4 provide PWM output)
  • Arduino Pins reserved:
    • 10 to 13 used for SPI
    • 4 used for SD card
    • 2 W5100 interrupt (when bridged)
  • Analog Input Pins 6
  • DC Current per I/O Pin 40 mA
  • DC Current for 3.3V Pin 50 mA
  • Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
  • SRAM 2 KB (ATmega328)
  • EEPROM 1 KB (ATmega328)
  • Clock Speed 16 MHz
  • W5100 TCP/IP Embedded Ethernet Controller
  • Power Over Ethernet ready Magnetic Jack
  • Micro SD card, with active voltage translator

Arduino Ethernet Dimensions:

  • Length 2.7"
  • Width 2.1"

Arduino Ethernet Package:

  • 1 x Arduino Ethernet w/o POE Module 

Arduino Ethernet Resources:

Sort by: Recently  /  Helpful Write review

Good Product

By Ajay from Panjab, India on April 25, 2016
Good packing
solid product
2 of 4 people found this review helpful
Was this review helpful to you?   Yes   No
    • Q


    • Is it possible to interface 2.8 inch Arduino Touch LCD Shield with Arduino Ethernet w/o POE Module (Arduino-Italy) successfully ?

      asked by Jaymin Dabhi on September 05, 2016
    • A

    • 2.8 inch Arduino Touch LCD Shield is pin compatible with this board Arduino Ethernet w/o POE Module (Arduino-Italy) and works successfully. However the presence of serial programmer's header can cause slight difficulty to fix both the modules perfectly. If the header near the ICSP can be removed both the devices can fit in properly.

Also purchased

Ask a question about Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)

Report issue about the Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)



Ask a question about the Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)

Report issue about the Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)



Request price match for the Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)

Found this item with same quality and at a lower price but prefer to buy from rhydoLABZ.com?

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

Arduino Ethernet w/o POE Module (Orginal Arduino-Italy)



Sponsors