- Stock: In Stock
- Brand: Waveshare
- Model: DEV-3367
- Weight: 0.22kg
- MPN: 10026
STM32 Development Board, Supports Arduino, Compatible With NUCLEO-F103RB
- Compatible with NUCLEO-F103RB, onboard Cortex-M3 microcontroller STM32F103RBT6
- Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources
- ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion
- Supports mbed, build prototype quickly by mbed SDK and online tools
- Comprehensive free software HAL library including a variety of software examples
- Comes with a separated ST-LINK/V2 module
COMPARE | XNUCLEO | NUCLEO | REMARKS |
Arduino compatibility | UNO, Leonardo | UNO | XNUCLEO can be configured by jumper to compatible with UNO (default) or Leonardo |
Arduino ICSP interface | Yes | None | ICSP is required by certain kinds of shields |
USB connectivity | Yes | None | The USB connector of NUCLEO is for debugging ONLY, not available for USB connection |
USB connector | Micro USB | Mini USB | Micro USB is the advanced USB standard |
Morpho headers mark | Most | None | Now you can check the PCB mark instead of datasheet |
Common interfaces are connected via | Jumpers | 0Ω Resistors | Jumpers are much easier to use, need no soldering |
UART debugging | Available while in-circuit debugging | Not available while in-circuit debugging | The NUCLEO integrated ST-LINK/V2 functional chip can be simulated as serial port, however, it's not available while in-circuit debugging, whereas XNUCLEO features a stand-alone USB TO UART chip |
8MHz crystal | Yes | None | Timer is more accurate when using external 8MHz crystal |
32.768KHz crystal | Yes | None | Required for RTC |
USB fuse | Yes (500mA) | None | The computer USB interface might be harmed without fuse |
LEDs | 4 | 1 | The more LEDs, the easier to monitor program running status |
UART indicator | Yes | None | Data communication is visible now |
DC input | Yes | None | A convenience |
Button position | Close to PCB edge | Close to Arduino connector | The button won't be untouchable when connecting with an Arduino shield if it were close to the PCB edge |
ST-LINK | Separated | Integrated | ST-LINK can be used anywhere else |
Comes with USB cable | Yes | None |
1. STM32F103RBT6
- Core : ARM® 32-bit Cortex™-M3
- Operating frequency : 72MHz
- Operating voltage : 2.0V-3.6V
- Package : LQFP64
- Memories : 128kB Flash, 20kB SRAM
- Interfaces : 2 x SPI, 3 x USART, 2 x I2C, 1 x CAN, 1 x USB
- AD/DA : 2 x AD (12 bit, 16 channels)
2. SPX3819M5 : 3.3V voltage regulator
3. AMS1117-5.0 : 5.0V voltage regulator
4. CP2102 : USB to UART convertor
5. Arduino connector : for connecting Arduino shields
6. ICSP interface : Arduino ICSP
7. USB TO UART : for debugging
8. USB connector : USB communication interface
9. SWD interface : for programming and debugging
10. ST Morpho headers : access to VCC, GND and all the I/Os, easy for expansion
11. 6-12V DC input
12. User button
13. Reset button
14. Power indicator
15. User LED
16. 500mA fast self-recovery fuse
17. Serial port Rx/Tx indicator
18. 8MHz crystal
19. 32.768KHz crystal
20. ADC/I2C selection jumper
- Short A and B : Arduino A4, A5 is used as I2C
- Short B and C : Arduino A4, A5 is used as ADC
21. UART selection jumper
22. MCU current test jumper : for low power tests
23. Power selection jumper
- Short 5V and U5V : powered from USB connection
- Short 5V and E5V : powered from external power supply
24. USB enable jumper
- Short the jumper to enable
- Open the jumper to disable
25. User button jumper
- Short the jumper to connect to I/Os used in example code
- Open the jumper to connect to other custom pins via jumper wires
26. User LED jumper
- Short the jumper to connect to I/Os used in example code
- Open the jumper to connect to other custom pins via jumper wires
- 1x XNUCLEO-F103RB
- 1x ST-LINK/V2 (mini)
- 1x USB Type A Plug to Micro B Plug Cable
- 1x USB Type A Plug to Receptacle Cable