EC200 4G LTE / 2G / GSM Industrial Grade Modem ( UART/USB ) - rhydoLABZ

                                                                   4G LTE / 2G / GSM  -  Industrial Grade Modem

OVERVIEW

This is a 4G LTE / 2G / GSM  - Industrial Grade Modem Board , which is professionally designed with 4 layer Gold plated PCB having industrial grade protections. It is built with Multi-Band 4G LTE module, Quectel EC200U-CNAC-N05-SNNSA LTE Cat 1 module optimized specially for M2M and IoT applications. It delivers maximum data rates up to 10 Mbps downlink and 5 Mbps uplink.

By default the board is populated with Push-Push Nano SIM socket, which can be replaced with normal Push-Pull type SIM Socket as well on special request.                                

EC200U series Modem has a rich set of Internet protocols, industry-standard interfaces and abundant functionalities (USB drivers for Windows 7/8/8.1/10, Linux, Android) extend the applicability of the module to a wide range of M2M and IoT applications such as POS/POC/ETC, shared equipment, data card, energy control and monitoring, security and protection, and industrial PDA.

This MODEM, built with support for 4G LTE/2G GSM networks, will automatically rollback to 2G mode in the absence of 4G Network, which will enable you to use it across the entire country including remote villages where 4G towers are less populated . MODEM supports UART communication ( Compatible with 3V3 & 5V microcontrollers) as well as USB interface with USB Powering option. Industrial grade Protections are provided for Noise,Spikes, Anti Static voltages & Surges coming through Power supply, USB, Antenna UFL Connections and through SIM Sockets. 

The Modem is populated with high quality Gold plated branded U.FL Connectors for 4G Main antenna. All this antenna networks are carefully designed with RF PCB design layouts and proper impedance matching networks for ensuring maximum signal gain and RF power delivery. 

This modem is built with Low dropout Linear Voltage Regulator having current capacity of 3Ampere to deliver enough current on demand, which will help modem to works properly on low signal range environments. Due to populated LDO regulator, Modem can be powered by DC voltage ranges from 5V DC to 12V DC. It is built with option to select interfacing voltage level (logic level voltage) based on user host controller, which allows you to connect 3V3 or 5V Micro-controller without any extra level conversion IC. In order to attain High Speed data communication between Modem and External Micro-controller, the board is built with TXB0108 voltage level translator IC, instead of low cost Resistive divider or reverse biased diodes/Mosfet.

Apart from the Power & UART Communications, most of the important Status, Control and LED pins are made available at on board 2mm pitch RMC Connectors for advanced users. The RMC connectors are separated based on its function and usability. For simple application ,user can make use of just two RMC connectors like Power, UART and leave all other RMC connector pins as open. Advanced users can make use of other RMC connectors for getting more functions.

C-Type USB Connector is provided for USB interface as well as for powering the MODEM, which are protected by onboard TVS IC. Even though the MODEM allows powering via USB from LAPTOP, we do not recommend it as the current available from LAPTOP USB ports are limited and may not be sufficient to support the modem on extreme demand conditions like out of range areas. Connectors like SIM socket,USB ports and Antenna Connectors are protected from Anti Static High Voltages using ESD protection ICs. 3 Nos onboard LEDs are provided to know the modem status like Power, Status and Net. Most of the required I/O pins are made available at Berg strip Headers (connector not populated). Most of the serial port status and control pins are also made available on separate RMC Connectors.

In order to reduce power consumption, Modem power ON/OFF options are provided on RMC connector. User can completely Turn ON/OFF the modem power supply using this pin from an external microcontroller GPIO Pins. Apart from this, PKEY pins are also made out of connector to Start and Stop the modem externally. In order to reduce the GPIO pins required to control the modem, by default the modem is configured to start automatically once it is powered and if needed this can be controlled manually through PKEY pins available on RMC connector.

The EC200U has strong extension capability with rich interfaces including UART, USB2.0 GPIO etc. With abundant application capability like TCP/IP/IPV4/IPV6/Multi-PDP/FTP/FTPS/HTTP/HTTPS/DNS, the module provides much flexibility and ease of integration for customer's application.The Modem is having internal TCP/IP stack to enable you to connect with internet via 4G LTE/2G/GPRS. It is suitable for SMS, Voice as well as DATA transfer application in M2M applications. 

Note: This 4G UART modem is coming with VoLTE support , which will enable you to use JIO sim card on it

Features of 4G LTE/2G/GPRS  UART/USB modem:

• Modem Support UART and USB Communication 
• High quality professionally designed Industrial Grade Modem(Made in INDIA)
• 4 Layer Gold Plated PCB for industrial grade performance.
• Built with EC200U-CNAC-N05-SNNSA Module from QUECTEL
• Works with 4G LTE/ 2G GSM GPRS Networks
• Automatic Fallback to 2G incase of absence of 4G Network
• Internet Protocol:TCP/IP/IPV4/IPV6/Multi-PDP/FTP/HTTP/DNS
• Support RNDIS/PPP/ECM ,MQTT/MQTTS ,TLS1.2 ,LBS
• Firmware update via USB/FOTA* 
• EC200U support VoLTE to work with Jio sim
• Onboard UFL connector for External 4G LTE Main antenna
• Onboard C-Type USB Connector for USB Communication, Modem Power and module firmware updating
• All important Status , Control and Communication pins are made available at different RMC connectors.
• Option to Turn ON/OFF Modem Power using Host Microcontroller GPIO pins.
• Option to automatically Turn ON Power and Start the modem on powering.
• LM39302 linear LDO voltage regulator is used for providing high-current output.
• Onboard TXB0108 voltage level translator IC which helps to interface with 3V3 & 5V External MicroControllers
• Onboard LED for power indication, Network and status.
• Header option for interfacing ADC,I2c,SPI
• Populated with Transient Voltage Suppressor and Anti Static Protection ICs 
• 4 Nos of 3mm Mounting Holes are Provided 
• Input voltage : 5V-12V DC / 2Amp
• Working temperature:-40°C ~85°C

Specifications:

• Operation temperature   :   -40°C to +85°C
• Bandwidth   :   1.4/3/5/10/15/20MHz
• Dimension   :   64MM x 48MM
• Frequency Bands   :   LTE-FDD: B1/B3/B5/B8 , LTE-TDD: B40/B41, GSM/GPRS/EDGE: B3/B8

        Specifications for Data transfer of  Module:

• LTE CAT1   :   Uplink up to 5Mbps , Downlink up to 10Mbps
• GPRS   :   Uplink/Downlink up to 85.6Kbps
• Protocol Supported   :   TCP/UDP/PPP/NITZ/PING/FILE/MQTT/NTP/HTTP/HTTPS/SSL/FTP/FTPS/ CMUX/MMS
• RIL Driver   :   Android 4.x–11.x
• USB RNDIS Driver   :   Windows 7/8/8.1/10, Linux 2.6–5.12
• USB ECM Driver      :    Linux 2.6–5.12
• USB Serial Driver    :   Windows 7/8/8.1/10, Linux 2.6–5.12, Android 4.x–11.x

Dimension of the Board:

Package includes:

• 1 x 4G LTE / 3G / 2G / GPRS   (UART / USB)  Modem Board 
• 1 x 2 pin RMC connector
• 1 x 4 pin RMC connector
• 1 x 5 pin RMC connector
• 1 x 6 pin RMC connector
  
  

Note:  Antennas are not included in standard package, if needed , please select Antennas and UFL-SMA cables from optional items listed above (near product price).

Development Resources:

• EC200U Datasheet
• EC200U AT Commands
• EC200U Hardware Design Guide