Menu
Your Cart
Dear Valued Customers: We're excited to announce our move to a new website!  Existing Customers, kindly utilize the 'Forgot Password' option to update the Password. Thank you for your cooperation!

Sparkfun ESP8266 Thing - Dev Board (With Headers)

Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
Sparkfun ESP8266 Thing - Dev Board (With Headers)
  • Stock: In Stock
  • Brand: Sparkfun - USA
  • Model: WRL-3266
  • Weight: 0.03kg
  • MPN: WRL-13804
Rs 1,299

This is the SparkFun ESP8266 Thing Dev Board — a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means  no need of any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.

The name “Thing” is due to the perfect foundation for your Internet of Things (IoT) project. The Thing does everything from turning on an LED to posting data with phant.io, and can be programmed just like any microcontroller. You can even program the Thing through the Arduino IDE by installing the ESP8266 Arduino add-on.

The ESP8266 Thing Development Board is a relatively simple board. The pins are broken out to two parallel, breadboard-compatible rows. The USB connector sits next to an optional power supply input, and an ON/OFF switch — controlling power to the ESP8266 — sits next to that. And LEDs toward the inside of the board indicate power, charge and status of the IC. The ESP8266’s maximum voltage is 3.6V, so the Thing has an onboard 3.3V regulator to deliver a safe, consistent voltage to the IC. That means the ESP8266’s I/O pins also run at 3.3V; need to level shift any 5V signals running into the IC. If  project requires a power source other than USB, the Thing Dev Board includes footprints for a 2-pin JST, 2-pin 3.5mm screw terminal, or a simple 0.1"-pitch 2-pin header. Unlike the original ESP8266 Thing, the ESP8266 Thing Dev Board does not have a built-in LiPo charger.

The Thing Dev Board even includes a PCB trace antenna as a default WiFi antenna. It’s cost-effective and works really well! If needed to connect a more sensitive antenna, or need to route outside an enclosure, a U.FL connector is also available on the board. Some soldering will be required to get the U.FL connector functioning, but instructions can be found in the Hookup Guide we have written for the dev board.

Specifications of Sparkfun Esp8266 Thing - Dev Board (With Headers):

  • All module pins broken out
  • Onboard FTDI USB-to-Serial
  • 802.11 b/g/n
  • WiFi Direct (P2P), soft-AP
  • Integrated TCP/IP protocol stack
  • Integrated TR switch, balun, LNA, power amplifier and matching network
  • Integrated PLLs, regulators, DCXO and power management units
  • Integrated low-power 32-bit CPU could be used as application processor
  • +19.5dBm output power in 802.11b mode
  • Pre-Soldered Headers

Resources:

Write a review

Please login or register to review