Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors

(0) 0 out of 5 stars Write reviewReport bug
  • Part No :
  • MOT-3111
  • Availability:
  • In Stock
  • Shipping :
  • Same Day
  • Weight:
  • 0.3Kg
  • Made By:
  • Pololu - USA
  • Mfr.Part.No:
  • 3499
  • Quality Rank:
  • 90/100
Price:
Rs 749
(Tax Excl.)
749.0000 rhydoLABZ.com New In Stock
Quantity :

Magnetic Encoder Pair Kit For 20D Mm Metal Gearmotors, 20 Cpr, 2.7-18V  uses a magnetic disc and Hall effect sensors to provide 20 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or any other digital circuit. This module is compatible with all dual-shaft 20D mm metal gearmotors. This kit includes two dual-channel Hall effect sensor boards and two 10-pole magnetic discs that can be used to add quadrature encoding to two 20D mm metal gearmotors with extended back shafts (motors are not included with this kit). The encoder board senses the rotation of the magnetic disc and provides a resolution of 20 counts per revolution of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output shaft, multiply the gear ratio by 20.This compact encoder solution fits within the 20 mm diameter cross section of the rear of the motors on three of the four sides. The fourth side of the encoder has the signal and power connections, and it extends 3 mm past flat edge of the motor. The assembly does not extend past the end of the extended motor shaft, which protrudes 6 mm beyond the back of the motor.


The encoder board is designed to be soldered directly to the back of the motor, with the back shaft of the motor protruding through the hole in the middle of the circuit board. One way to achieve good alignment between the board and the motor is to tack down the board to one motor pin and to solder the other pin only when the board is flat and well aligned. Prolonged heating of the motor pins  could deform the motor case or brushes. Once the board is soldered down to the two terminals, the motor leads are connected to the M1 and M2 pads along the edge of the board; the remaining four pads are used to power the sensors and access the two quadrature outputs:The sensors are powered through the VCC and GND pins. VCC can be 2.7 V to 18 V, and the quadrature outputs A and B are digital signals that are either driven low (0 V) by the sensors or pulled to VCC through 10 kΩ pull-up resistors, depending on the applied magnetic field. The sensors’ comparators have built-in hysteresis, which prevents spurious signals in cases where the motor stops near a transition point.Once the board is soldered to the motor, the magnetic encoder disc can be pushed onto the motor shaft. One easy way to accomplish this is to press the motor onto the disc while it is sitting on a flat surface, pushing until the shaft makes contact with that surface.Pushing the disc a little closer to the PCB can ensure strong signal and good performance.

 

Note: This sensor system is intended for users comfortable with the physical encoder installation. It only works with 20D mm metal gearmotors that have extended motor shafts.

Specifications:

  • Minimum operating voltage: 2.7 V
  • Maximum operating voltage: 18 V

Dimensions:

  • Size:  20 mm × 16.5 mm
  • Weight:  2.4 g

Package includes:

  • 2 x   dual-channel Hall effect sensor boards
  • 2 x   10-pole magnetic disc

Resources:

Sort by: Recently  /  Helpful Write review

There are currently no any reviews about this product.

There are currently no any question about this product.

Ask a question about Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors

Report issue about the Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors



Ask a question about the Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors

Report issue about the Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors



Request price match for the Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors

Found this item with same quality and at a lower price but prefer to buy from rhydoLABZ.com?

Please submit the url of the better price you saw. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. We will notify you the result by email. Thanks a lot for helping us to maintain competitive prices.

Magnetic Encoder Pair Kit For 20D mm Metal Gearmotors