Description: The eCee PIC18F4580 Development Board can be used to evaluate and demonstrate the capabilities of Microchip PIC18F4580 microcontroller. The board is designed for general purpose applications and includes a variety of hardware to exercise microcontroller peripherals. Ideally suitable for training and development purposes.
eCee PIC18F4580 Features
• Compact and Ready to use design
• Professional and Fully EMI/RFI Complaint PCB Layout Design for Noise Reduction
• High Quality Two layer PTH PCB
• Includes PIC18F4580 Microcontroller with built-in CAN Peripheral
• Board Supports PIC 16F877/18F 4520/4550* Microcontrollers
• No separate programmer required (Built in Boot loader)
• No Separate power adapter required (USB power source)
• Screw terminal for External power Supply (with Jumper Select Option)
• External Power Supply range of 7V to 20V
• Adaptor (any standard 9-12V power supply) option
• RS-232 Interface (For direct connection to PC’s serial port)
• On board Two Line LCD Display (2x16)
• On board I2C EEPROM (4K-AT24C04).
• On board I2C RTC (DS 1307) with Crystal and Battery
• Four multiplexed 7-Segment LED Display
• Built in Matrix keyboard (12 keys)
• Built in Pull-Up (4 Keys) Keyboard
• Built in IR Sensor Interface – TSOP 1738
• Built in 8 LED Interface to test I/O
• On Board External Interrupt and Reset buttons
• Built in Pot interface to ADC
• On Board Temperature Sensor Interface (LM35)
• On Board Buzzer Interface
• On Board PWM Output pin • On Board ICD Connector for Debugging/Programming
• On Board ICSP Connector
• On Board 20 MHz Crystal Oscillator
• On Board Power LED Indicator
• All Port Pins available at IDC (2x5) Connector
• Can be used as main board for developing applications
• Power Supply Reverse Polarity Protection
• On Board 1 Amp Voltage Regulator
• Demo HEX codes included for testing of board features
• Example codes included
PIC 18F4580 Chip Specification
•Microchip PIC 18F4580 with 20 MHz Crystal Oscillator (With Boot loader Software)
•Built-in CAN Peripheral
•High Performance RISC CPU
•32 KB Programmable Flash Memory
•1536 bytes Data Memory (SRAM)
•256 bytes EEPROM
•Supports Up to 40 MHz Operation
•36 I/O pins
•11-Channel 10-bit Analog to Digital Converter(ADC)
•One Capture module/ Compare Module/PWM Module
•One Enhanced Capture Module/ Compare Module/ PWM module
•One ECAN Module with Message bit rates up to 1 Mbps
•Parallel Communications (PSP) Support
•One 8-Bit Timer/Counter and Three 16-Bit Timer/Counter
•One Enhanced USART (Supports RS-232, RS-485 and LIN 1.3)
•One Master Synchronous Serial Port (MSSP)
•One Serial Peripheral Interface(SPI) Module
•One Inter-Integrated Circuit (I2C) Module
•Power-On Reset (POR), Power-Up Timer (PWRT) and Oscillator Start-up Timer (OST)
•Interrupt Capability (up to 20 sources)
•Three External Interrupts
•In-Circuit Serial Programming (ICSP) via two pins
•In-Circuit Debug (ICD) via two pins
•Self Programmable under software control
•Programmable Brown Out Reset
•Low Voltage Programming
•Power Saving Sleep Mode
•Extended WatchDog Timer(WDT)
•Wide Operating Voltage 2.0V to 5.5V
•Low Power Consumption using nanoWatt Technology
eCee PIC18F4580 Package Includes
•Fully Assembled and Tested eCee PIC18F4580 Development board
•Software CDROM with
Schematic
Programming Software
Sample Hex Code
Example Codes
Downloads:
Quick Start Manual
