Description:The all New AVR ATmega16
Development Board-Mini can be used to evaluate and demonstrate the
capabilities of AVR ATmega16 microcontrollers. Since all I/O pins are
broken out on Male and female Berg strips, it is very easy to use for
development purpose as well. The board is designed for general purpose
applications and it includes a variety of hardware to exercise
microcontroller peripherals. Onboard Mini Bread board is provided to
ease the use,Ideally suitable for training and development purposes.
Apart from this there is an onboard 2MM pitch Female sockets on both
bottom and top side to insert
Xbee module as per convenience. Since
there are different modules (
GPSBee,
Bluebee,RFBee Etc) are available in
the XBEE form factor, it will be easy to interface and experiment all of
them. Onboard 5v to 3v3 MOSFET based level converter and 3V3 Voltage
regulator provide safe interface to XBEE and other low voltage devices.
The onboard 5V regulator is having current rating of 1A and 3V3 voltage
regulator is having 500mA capacity to easily power almost all onboard
devices as well as external devices. All I/O pins and Power pins (5V
& 3V3) are made available at Female header pins around the
Breadboard to ease the wiring. Apart from this the All I/O pins are
ready at male berg strips in two rows under the LCD. The UART pins are
available at separate RMC Connector with power (VCC & GND). A
3v3UART is provided with the help of onboard MOSFET voltage level
converter.Â
Â

 The onboard mini-B type USB
connector can be used to power the board as well as to communicates with
PC. A jumper is provided to select the PC interfacing method (USB or
RS232). The development board can be programed by internal bootloader or
ISP Programmer or separate JTAG programmer/debugger. Separate 10 pin
shrouded male connector has been provided to connect JTAG programmer and
ISP Programmer. Apart from USB the board has two more powering options
like DC Adapter jack and 2Pin RMC connector with Reverse polarity
protection. Available onboard peripheral interfaces are 3 nos Pull-up
switches,3 nos LEDs, buzzer, Analog Temp sensor, Analog POT,16X2
LCD,RS232,USB,Voltage Level Converter and connectors for xbee, sockets
for RFID Module (EM18 or uRFID), SERVO Motor, UART, JTAG etc.

 All these peripheral interfaces can be disconnected by removing onboard PCB jumpers to free up the I/O PINS for other purposes.
Features: - Includes AVR ATmega16 MicrocontrollerÂ
- Compact and Ready to use designÂ
- Professional EMI/RFI Complaint PCB Layout Design for Noise Reduction
- High Quality Two layer PTH PCB
- No separate programmer required (On-Chip Boot loader)
- No Separate power adapter required (USB power source)
- RS-232 Interface (For direct connection to PC's Serial port)
- USB Interface to connect to PC
- On Board Mini Breadboard for experiments
- On Board Two Line LCD Display (2x16)
- POT for LCD Contrast controlling
- On Board 3 LED Interface to test Port pin (with jumper select option)
- On Board Analog Pot interface to ADC (with jumper select option)
- On Board Analog Temperature Sensor InterfaceÂ
- On Board Buzzer InterfaceÂ
- On Board 3button Pull-up Keyboard interface
- On Board 3.3V Regulator
- On Board Reset Switch
- On Board Connector for interface SERVO motor
- On Board Connector to interface Xbee module on top/bottom side
- On Board Connector to interface EM-18 compatible µRFID Reader module on top side
- On Board Power LED Indicator
- Adapter (any standard 9-12V power supply) optionÂ
- All Port Pins available at Male Berg StripÂ
- All Port Pins available at Female Berg Strip around Bread board
- On Board JTAG Connector for Debugging/Programming
- Power Supply Reverse Polarity Protection
- On Board DB9 Connectors (for UART)
- On Board USB Connector
(for POWER/UART)
- On Board 4 pin RMC connector (for UART)
- On Board 1 Amp Voltage Regulator
- On Board regulated 3V3 output
- On Board regulated 5V output
- Can be used as main board for developing applications
- On Board ISP connector
- On Board 8 MHz Crystal OscillatorÂ
- jumper selection option for Analog reference voltage (3v3 or 5v)
AVR ATMega16 Chip Specification:
- 16 K bytes programmable flash
- 1 K bytes SRAM
- 512 bytes EEPROM
- 16 MHz operation (Up to 16 MIPS)
- 32 I/O pins
- 8 channel 10 bit ADC
- 4 PWM Channels
- Two 8-Bit Timer/Counter
- One 16-Bit Timer/Counter
- One Serial USART
- 1 Two Wire Serial Interface TWI
- SPI Master/ Slave
- Power Consumption ~Â 14 mA
- Operating voltage
- 2.7 to 5.5V for ATmega16(L)
- 4.5 to 5.5V for ATmega16
Package includes:
- 1 x Fully Assembled and Tested Development board-Mini
- 1 x RS232 Serial Cable DB9 M/F
- 1 x USB miniB Cable
- 5 x jumpers(2mm)
- 4 x Spacers
- 8 x screws
- 1 x 2-Pin RMC Female connector With Wire -2.54Mm Pitch
- 1 x Software CDROM with
- Schematic
- Programming Software
- Sample Hex Code
- Example Codes
Documents:
There are currently no any question about this product.